COTS PRODUCTS > COTS DIGITAL / ANALOG PRODUCTS > Single Board Computers > AT-cPCI-SBC-ATOM-6U
 
Dual Slot (8HP) CompactPCI Single Board Computer
CompactPCI System Controller
Compliance to PICMG 2.0 R3.0 CompactPCI Specification
8 GPIO
Compact Flash site
High speed CANbus controller
Up to two Dual redundant 1553B channel programmable as BC/RT/MT (Refer Ordering information for 3U and 6U form factor)
Up to 8Tx and 8Rx ARINC429 Channels (Refer Ordering information for 3U and 6U form factor)
Windows® XP SP3, XPe, WES 7, CE, Linux, VxWorks, QNX OS are available
Single PMC mezzanine site (Available only in 6U form factor)
On Card ETX Computer On Module specification:
> 1.0 GHz INTEL Atom Processor E640T
> 1 GByte of DDR2-800
> Up to 4 GB NAND Flash
> One 10/100/1000 Mbps Ethernet interfaces
> One serial ATA external
> 6x USB 2.0 (boot) + 1x USB Client
> Two Serial channel ports
> Two COM Ports
> High definition stereo audio
> Real Time Clock and Watchdog timer
> Temperature Sensor
 

The AT-cPCI-SBC-ATOM is an exceptionally high integration, high performance, rugged, and high quality board, with cPCI Back Plane Interface. The cPCI board has a Computer On Module plugged in to it. ETX is based on one of the ultra high performance, high-integration 1.0 GHz INTEL Atom Processor E640T, and gives designers the choice of a complete, rugged, embedded processor based on the ETX form factor that conforms to the ETX V2.7 specification. The module plugs into the card, which has connectors and additional circuitry to meet your application requirements. The image shown above is 3U cPCI SBC ATOM,

This product provides a suitable solution in an embedded market wanting low power and small size. It utilizes the Intel® Platform Controller Hub EG20T to support up to 1 GB of DDR2 -800. The Computer On Module incorporates a range of I/O interfaces including One Gigabit Ethernet port, two serial ports, six USB ports, CAN bus speed upto 1 Mbps and High Definition Audio, 4 GB NAND Flash, one serial ATA and a number of user defined GPIO’s.

The AT-cPCI-SBC-ATOM has implemented all its Discrete IO logic in the FPGA. All discrete inputs and outputs are accessed through registers implemented inside FPGA. The card is particularly well suited to embedded applications and meets all the requirements such as power consumption, temperature range, quality, and reliability demands of embedded system applications. The card uses +5V, +3.3V and +12V from the Back Plane as primary supply voltages. All the internal Voltages required by FPGAs and various other peripherals are derived using on board regulators and DC-DC Converters. OS support for Windows® XP SP3, XPe, WES 7, CE, Linux, VxWorks, QNX are available.

CPU
Processor: INTEL Atom processor E640T
Clock Frequency: 1.0 Ghz
45nm process technology
L2 Cache: 512 KB of cache
32 KB Instruction Cache and 24 KB L1 Cache
320MHz Graphics Core Render Clock
Graphics Interface
Intel® Platform Controller Hub EG20T
Intel 2D/3D Graphics engine
LVDS 18/24bit 1280x768@60Hz; SDVO 1920x1080@50HZ
Memory
Onboard 1 GB DDR2-800
4 GB NAND Flash memory
4 MB of BIOS Flash EPROM
Mass Storage Interface
1 x Serial ATA external supporting 3 GB/s
One EIDE interface
> Supports an On-board Compact Flash site
Stereo Audio
Intel High Definition Audio interface
Communication Ports
One 10/100/1000 Mbps Gigabit Ethernet ports
6x USB 2.0 (boot) + 1x USB Client
One RS-232/422/485 port and one configurable RS232 port
Two COM ports
High speed CAN bus controller up to 1 Mbps
8 GPIO pins - software configurable
Peripherals
1 Real Time Clock
1 Watchdog timer and long duration timer
1 On-board Temperature sensor
MIL-STD-1553B
IPC1553 – Next generation 1553 core
2 Dual Redundant MIL-STD-1553B Channels
Supports MIL-STD-1553 A/B
Each channel is independently programmable as either Bus Controller, Remote Terminal or Bus Monitor
Complete message programmability
48-bit/100ns Time tagging
Direct or Transformer Coupled Bus Interface
ARINC429
IPC429 – Next generation A429 core
8 Transmit and 8 Receive Channels
Configurable for High Speed (100 Kbps) or Low Speed (12.5Kbps/50Kbps)
Up to 256 Label memory for each Receive channel
128 Word for Tx and Rx FIFOs for each Transmit and Receive channel
Asynchronous and Synchronous messaging
Programmable Interrupts
Programmable Refresh rates of 20ms to 200ms
Label selective trigger for Capture/Filtering and SDI filtering
CompactPCI Interface
Universal signaling support Compliant to PICMG 2.0 R3.0, 3.3V or 5V signaling levels
32-bit, 33/66 MHz interface
Operates as a System Slot Controller or operates in a Peripheral Slot
PICMG 2.1 R2.0 Hot Swap Compliant
Operating Systems
Windows® XP SP3, XPe, WES 7, CE, Linux, VxWorks, QNX
Environmental: Temperature Range
-40°C to 85°C 5% to 95% Relative Humidity, non condensing
Mechanical
Dual slot (8HP)
Board Dimensions
6U:160mm x 233mm
3U:160mm x 100mm
Metal Heat sink covering over the card for efficient heat transfer from the card to the chassis
Card fitted with wedge locks on either side for firm seating in the slot
Power
Derived from +5.0V, +3.3V and +12V of Back Plane
All other voltages required for powering on-board devices are generated from on-board power circuitry
Warranty
1 year limited warranty
 
CORPORATE   ABOUT   FOLLOW US ON
AdTEC Electronics Inc.
4677 Old Ironsides Drive
Ste 230
Santa Clara, CA 95054
USA
 
AdTEC Electronics specializes in providing end-to-end custom product design & development encompassing System, Mechanical, Board Electronics, Chip design, Firmware and Application Software Engineering. Our design capabilities include design for testability and rugged design to meet both commercial and stringent regulations.
 
HOME ABOUT US COTS PRODUCTS SERVICES & SOLUTIONS SUPPORT & RESOURCES NEWS & EVENTS BLOG CONTACT US
AdTEC Electronics Inc.